| EX12 Extreme Resolution Active Speaker System |
|
|
The EX12 further builds on the success of the EX6 and EX10 by implementing the revolutionary 3” NVPD large format compression driver found in our flagship VHD range of products. This makes for one of the most perfectly balanced and accurate, compact, 2-way active boxes available on the market today. Complete on-board control courtesy of electronic crossovers, phase alignment, equalization and speaker protection all integrated into the EX12’s amplifier module. |
|
| Applications |
|
- High quality fixed installations.
- Portable PA Systems for AV, speech and multimedia playback.
- Small to medium-sized Live Music applications.
- Mobile DJ (when used with EX2.2 or EX2.5 Active Bass Module).
- Floor monitoring applications.
|
|
| Features |
|
- Professional, Baltic birch construction with wear resistant polymer coating.
- 127dB sustained output, 130dB peak with very high dynamic range and low noise floor.
- 500W of total power with complete on-board speaker management system.
- 450W high efficiency, current enhancing, switching low frequency amplifier
- Very high quality 50W, low IM distortion, Class AB, high frequency amplifier with
transformer balanced output.
- Compact asymmetrical trapezoidal design allows for use in stage monitor or
under balcony applications with high pass filter to adjust equalisation and phase response.
- Wide dispersion 80° H x 40° V horn.
- New state of the art 3” (76mm) Nitride Titanium diaphragm compression driver
with complex geometry phase plug and neodymium magnetic structure for higher
output, exceptionally low distortion and extended frequency response.
- 12” woofer with revolutionary Active Impedance Control (AIC) voice coil
technology and neodymium magnetic motor structure dramatically increases force, lowers
distortion and provides increased frequency response linearity.
- Proprietary top and side handle designs for simplified handling and carrying, integrates
one M10 hang point, OmniMount™ bracket point and four M6 bracket points.
- Ten additional M10 suspension points for flexible rigging and installation options.
- Top hat for pole mounting applications.
- LED indicators for signal present, limiter, thermal condition and power ON status.
- EX12T only, four steel ‘fly-clip’ anchor points, two on top and two on bottom.
|
|
| Specifications |
| |
| Product |
EX12 |
| System Acoustic Perfomance |
|
| -3dB Response |
65Hz - 20kHz |
 |
| -10dB Response |
45Hz - 30kHz |
|
| Max SPL Long-term |
127dB |
|
| Max SPL Peak |
130dB |
|
| Crossover Point |
1.1kHz |
|
| |
| High Frequency Section |
|
| Throat Exit Diameter/ Diaphragm Size |
1.4" / 3" |
|
| Diaphragm Material |
Nitride Titanium |
|
| Magnet Type |
Neodymium |
|
| Horn with Constant Directivity Coverage Horizontal/ Vertical |
80° x 40° |
|
| |
| Low Frequency Section |
|
| Acoustic Design |
Front Loaded, Bass Reflex |
|
| Woofer Size/ Voice Coil Diameter/ Design |
12" / 2.5" / Trans Coil |
|
| Diaphragm Material |
Epoxy Reinforced Cellulose |
|
| Magnet Type |
Neodymium |
|
| |
| Signal Input |
|
| Input Impedance |
20 kΩ |
|
| Input Sensitivity |
1.0V rms |
|
| |
| Power Connector |
|
| Power Connector |
Neutrik PowerCon® |
|
| |
| High Frequency Amplifier |
|
| Type |
Class AB Push-Pull |
|
| Rated Continuous Power |
50W |
|
| Distortion |
<0.05% |
|
| Operating Bandwidth |
1.1kHz - 30kHz |
|
| |
| Physical Dimensions |
|
| Height |
596mm (23.46") |
|
| Width |
368mm (14.48") |
|
| Depth |
368mm (14.48") |
|
| Weight |
29kg (63.8lbs) |
|
| |
| Bass Amplifier Specification |
|
| Type |
High Efficiency Switching |
|
| Rated Continuous Power |
450W |
|
| Distortion |
<0.05% |
|
| Operating Bandwidth |
45Hz - 1.1kHz |
|
| |
| Recommended Amperage |
|
| Recommended Amperage |
6A 115V | 3A 230V |
|
| |
| Operating Voltage |
|
| Operating Voltage |
100 - 120V @ 60Hz | 230 - 250V @ 50Hz |
|
| |
|
|
| Configurations |
|
.gif)
|
| Accessories |
| |
|
| Downloads |
| |
|
.gif)
.gif)
